川禾-新闻

Briefly describe the intelligent cutting function of metallographic cutting machine

2020.10.30

Metallographic sample preparation is a technical job, especially cutting. The quality of cutting directly determines whether the entire sample preparation process can be successful, so it is very critical. Metallographic cutting is to cut the original sample to obtain the most representative target analysis surface. Cutting is essentially the process of removing the slit material. The cutting blade rotates at high speed to make the hard abrasive protruding on the surface impact the sample, and the sample is cut by self-loss.

查看详情

金相切割的常见问题

2020.10.30

一般来说，金相制样包括切割，镶嵌和磨抛三大步骤。顾名思义：切割是分切原始样品，获取最具代表性的目标分析面。镶嵌则是将切割后的样品放入填埋树脂内，形成标准的样品便于后续磨抛处理。磨抛是把目标分析面平整化处理，消除划痕，便于后期显微观测使用。

查看详情

如何选择金相切割片

2020.10.30

优质切割片会让切割过程感觉轻快，切割表面均匀平整，同时又能做到锯片寿命较长。能平衡好这三点并非易事，川禾公司依据金相切割工况的特殊要求，精心挑选上乘磨料颗粒，优化磨粒的粒度分布，使用高结合力树脂粉料，反复优化成型工艺参数，开发出适合金相切割专用锯片。

查看详情

优质金相切割机的特征

2020.10.30

金相制样是一门技术活，切割首先如此，切割的质量直接决定整个制样过程能否成功，所以非常关键。需要制样员对了解目标材料的基本状况，例如材料的硬度强度等力学性能指标，重点观察的部位，以及目标材料的禁忌要求。然后才能依据这些特点，制定恰当的切割工序。

查看详情

优质金相切割机的特征

金相制样是一门技术活，切割首先如此，切割的质量直接决定整个制样过程能否成功，所以非常关键。需要制样员对了解目标材料的基本状况，例如材料的硬度强度等力学性能指标，重点观察的部位，以及目标材料的禁忌要求。然后才能依据这些特点，制定恰当的切割工序。

2020.10.30 4019

查看详情
如何选择金相切割片

优质切割片会让切割过程感觉轻快，切割表面均匀平整，同时又能做到锯片寿命较长。能平衡好这三点并非易事，川禾公司依据金相切割工况的特殊要求，精心挑选上乘磨料颗粒，优化磨粒的粒度分布，使用高结合力树脂粉料，反复优化成型工艺参数，开发出适合金相切割专用锯片。

2020.10.30 2762

查看详情
A brief discussion on the importance of metallographic cutting discs

Cutting is the first step in the metallographic sample preparation process. The quality of cutting directly determines whether the entire sample preparation process can be successful, so it is very critical.

2020.10.30 1890

查看详情
The Importance of Metallographic Cutting Fluid

Cutting is the first step in the metallographic sample preparation process. The quality of cutting directly determines whether the entire sample preparation process is successful, so it is very critical.

2020.10.30 1775

查看详情
Common problems of metallographic cutting

Metallographic sample preparation is a technical job, which requires the sample maker to understand the basic conditions of the target material, such as the mechanical properties of the material such as hardness and strength, the key observation points, and the taboo requirements of the target material. Only then can the appropriate sample preparation process be formulated based on these characteristics.

2020.10.30 2525

查看详情
金相切割的常见问题

一般来说，金相制样包括切割，镶嵌和磨抛三大步骤。顾名思义：切割是分切原始样品，获取最具代表性的目标分析面。镶嵌则是将切割后的样品放入填埋树脂内，形成标准的样品便于后续磨抛处理。磨抛是把目标分析面平整化处理，消除划痕，便于后期显微观测使用。

2020.10.30 3089

查看详情
Briefly describe the intelligent cutting function of metallographic cutting machine

Metallographic sample preparation is a technical job, especially cutting. The quality of cutting directly determines whether the entire sample preparation process can be successful, so it is very critical. Metallographic cutting is to cut the original sample to obtain the most representative target analysis surface. Cutting is essentially the process of removing the slit material. The cutting blade rotates at high speed to make the hard abrasive protruding on the surface impact the sample, and the sample is cut by self-loss.

2020.10.30 2207

查看详情

Q&A